Thread: Update iAtkos S3 V2 10.6.3 To 10.6.8 All Machine

Why's shutdown not working? I used cleaned installing method, everything seem good. Which kexts are you using?

hello can anyone help me please because I install iATKOS on HP Pavilion S2 V2 dv6OOO and when it's the updated, its course ..... more .....

im fanally in iAtkhos update to 10.6.8, no problem in update, just 1 problem if i wanna shootdown my iatkhos notthing shootdown always in restart, please help me


Model Name: MacBook (no problem, normal running)
Model Identifier: MacBook4,1
Processor Speed: 1.73 GHz
Number Of Processors: 1
Total Number Of Cores: 1
L2 Cache: 1 MB
Memory: 2 GB
Bus Speed: 533 MHz
Boot ROM Version: MB41.0073.B00
SMC Version (system): 1.30f3
Serial Number (system): SOMESRLNMBR
Hardware UUID: 00000000-0000-1000-8000-001D7201E7E6

ATA Bus:

HL-DT-ST DVDRAM GSA-T20N:

Model: HL-DT-ST DVDRAM GSA-T20N
Revision: WP03
Serial Number: KZ17AL81138
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Low Power Polling: No
Power Off: No

Name: ethernet
Type: Ethernet Controller
Bus: PCI
Vendor ID: 0x11ab
Device ID: 0x4353
Subsystem Vendor ID: 0x1025
Subsystem ID: 0x0124
Revision ID: 0x0015
Link Width: x1
BSD name: en0
Kext name: AppleYukon2.kext
Location: /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleYukon2.kext
Version: 3.2.1b1
Intel GMA X3100:

Chipset Model: GMA X3100
Type: GPU
Bus: Built-In
VRAM (Total): 144 MB
Vendor: Intel (0x8086)
Device ID: 0x2a02
Revision ID: 0x0003
Displays:
Display:
Resolution: 1280 x 800
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Display Connector:
Status: No Display Connected

Memory Slots:

ECC: Disabled

Bank 0/M1:

Size: 1 GB
Type: DDR2 SDRAM
Speed: 532 MHz
Status: OK
Manufacturer: Kingston
Part Number: 9905295-015.A00LF
Serial Number: 0x8f0b3a38

Bank 1/M2:

Size: 1 GB
Type: DDR2 SDRAM
Speed: 532 MHz
Status: OK
Manufacturer: Kingston
Part Number: 9905295-029.A00LF
Serial Number: 0x94090533

Battery Information:

Model Information:
Serial Number: 830
Manufacturer: SONYCorp
Device name: AS07A41
Charge Information:
Charge below critical level: No
Charge below warning level: No
Charge remaining (mAh): 1200
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 1200
Health Information:
Cycle count: 2800
Condition: Replace Now
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 12259

System Power Settings:

AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 0
Automatic Restart On Power Loss: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes

Hardware Configuration:

UPS Installed: No

AC Charger Information:

Connected: Yes
ID: 0x0000
Wattage (W): 0
Revision: 0x0000
Family: 0x0000
Serial Number: 0x00000000
Charging: No

The printers list is empty. To add printers, choose Apple menu > System Preferences…, click Print & Fax, and then click Add (+).:

CUPS Version: 1.4.7 (cups-218.31)

Serial-ATA Bus:

FUJITSU MHZ2250BH G1:

Capacity: 250.06 GB (250,059,350,016 bytes)
Model: FUJITSU MHZ2250BH G1
Revision: 00400209
Serial Number: K61DT89285RN
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ata
Unit Number: 0
Socket Type: Serial-ATA
Partition Map Type: MBR (Master Boot Record)
S.M.A.R.T. status: Verified
Volumes:
Mac Os X:
Capacity: 31.45 GB (31,452,037,120 bytes)
Available: 22.55 GB (22,551,179,264 bytes)
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s1
Mount Point: /
Sydney:
Capacity: 72.87 GB (72,867,723,264 bytes)
Available: 72.66 GB (72,663,515,136 bytes)
Writable: Yes
File System: HFS+
BSD Name: disk0s5
Mount Point: /Volumes/Sydney
Untitled:
Capacity: 72.87 GB (72,867,723,264 bytes)
Available: 31 GB (30,996,004,864 bytes)
Writable: Yes
File System: Tuxera NTFS
BSD Name: disk0s6
Mount Point: /Volumes/Untitled
Untitled 1:
Capacity: 72.86 GB (72,859,497,984 bytes)
Available: 55.51 GB (55,514,054,656 bytes)
Writable: Yes
File System: Tuxera NTFS
BSD Name: disk0s7
Mount Point: /Volumes/Untitled 1

USB Bus:

Host Controller Location: Built-in USB
Host Controller Driver: AppleUSBUHCI
PCI Device ID: 0x2830
PCI Revision ID: 0x0003
PCI Vendor ID: 0x8086
Bus Number: 0x1d

Originally Posted by bomteam

Installation :

1.First update to 10.6.7 combo update. Instruction update 10.6.7 go to
http://www.osx86.net/10-6-snow-leopa...l-machine.html
2.After update 10.6.7 succes, remove or delete "caches folder" on library
3.Remove or delete "caches folder" on sytem/library
4.Run Disk Utility and click Repaired disk permissions
5.Restart or reboot
6.BackUp AppleACPIPlatform.kext & IOPCIFamily.kext on system/library/extensions folder
7.BackUp IOUSBFamily.kext & IOUSBMasstroageClass.kext on system/library/extensions folder
8.Run 10.6.8 ComboUpdate>wait to finish>Don't Restart or Reboot Computer
9.Copy AppleACPIPlatform.kext, IOPCIFamily.kext, IOUSBFamily.kext & IOUSBMasstroageClass.kext (U BackUp) to Sytem/Library/Extensions Folder
10.Run Kext Utility>wait to finish>Restart or Reboot Computer

Good Luck

hello friend, I was able to perform the update after many attempts, but now I have a problem, the usb does not work, I have an intel intel dx58s0 ... I would like to help me with the steps necessary to have the computer without any problem ... thanks

Originally Posted by yandryxx

hello friend, I was able to perform the update after many attempts, but now I have a problem, the usb does not work, I have an intel intel dx58s0 ... I would like to help me with the steps necessary to have the computer without any problem ... thanks

Dear Yandri, all you have to do is:
1. kext wizard (Kext Wizard 3.7.3 - Downloads - OSx86.net)
2. (http://www.osx86.net/view/961-voodoo...and_mouse.html) / (http://www.osx86.net/view/961-voodoo...and_mouse.html) if u available you have to do is:
1. Open kexts wizard> select instlation> browse to where you saved the kexts (no.2)> Open option> browse navigate to where you saved the file no.2> press alt (on windows = cltr) mark the 2 kext (PS2 Mouse & Keybord/AppleACPIPS2Nub.kext and PS2 Mouse & Keyboard/VoodooPS2Controler.kext
Destination mark System / Lybarry / Extension> adjust the target disk partitions to install mac os x (in this case I call my partition Mac Os X)> press install
if there are any error messages just continue or ok until finished (this is because the name of the kext is similar / same), after installed go to > Maentenance > mark Extra and System Labarry> press Execute, and then reboot your computer.



hasil moding.jpg



if wanna instal again i have tutorial for u to update 10.6.3 to 10.6.8 without problem, but in this i know u have noproblem with 10.6.3
if u needed thats replay me i can accept to repaly again for you, and where u come from, im from indonesia

yes kext evrething is okey, that is my screen shoot, evrething is okey just problem with shootdown can't shootdown always restart
apaa tuch.jpg

hmmm my computer aint workin with this the system is really slow after update and wont connect to the internet or recognize my usb drives

Hi.

Thanks for the method. But after following this method, I got to 10.6.8 and then I could never boot. It kept getting kps during the boot process. I downgraded back to 10.6.3 and came back up to 10.6.7. In the process I gained QE/CI but lost sleep. In fact, even though I have set sleep to 'never' it still crashes with a kp if left unused for a couple of hours. BUt I can live with that!

Would really like to get to 10.6.8 as that is rock solid on a regular mac (6 year old macbook).

This is what happens. I go into a weird situation where kexts would be loaded upto a point: DSMOS arrives, SMC is loaded etc. After it comes to ntfs drivers the screen goes black (too quickly for me to take a picture) and gives me a white block cursor - like a terminal window gone full screen. I can type and then see some info on the screen. After a few seconds, it goes back to the block cursor.

Booting with -s leads me to the same situation when I type exit. Booting with -x leads me to the login screen, but no mouse everytime and no keyboard some of the time. (weird!) I have reinstalled the AppleIntelACPI kexts from 10.6.7 using the boot dvd, but still no luck. I have also tried deleting caches and rebooting.

Is there anything that I can do?

Thanks again

A

Did you down load MacOSXUpdCombo10.6.8.dmg from apple and run it your self or did you just try to update from SoftwareUdate in the Apple menu at the top lefthand corner of your screen?

Do the download method.

Download MacOSXUpdCombo10.6.8.dmg
download legacy_kernel-10.6.8.v2.pkg.zip from this site
download Kext Utility.app.zip from this site if you don't have a copy.

mount the update dmg and run MacOSXUpdCombo10.6.8.pkg from it.
When it is finished DO NOT RESTART your computer yet.
Unzip and run legacy_kernel-10.6.8.v2.pkg. The installer program may quit. That is ok, just run it again.
Unzip and run Kext Utility.app to set all the permissions of both /Extra/Extensions and /System/Library/Extensions.

Now you can reboot.


MMM? Before I forget, this particular method is for AMD processor machines. For Intel machines the proceedure is the same but uses a different kernel. I am not sure what that one is.

Thanks Alaskan.

Yes I used 10.6.8 combo update - not software update. And I am on an Intel processor - core2duo on a 945 motherboard, with intel gma950 graphics.

I should have mentioned that. My apologies.

A